genie garage door starts to close then goes back up

The garage door will automatically go. OR Door will only open.

How To Reset A Genie Garage Door Opener

A while back my door started reversing maybe 8-10 above contact with the bottom and I plunged into readjusting the clutch and the limit switch without success Then after an hour of messing with it I realized the some long grass stems held by cobwebs to the bottom inside of the door were tripping the electric eye.

. If your garage door keeps going back up after youve closed it the most common reason is because. Your garage doors logic board is the brain of your garage door opener. If youre Genie Excelerator just stops when either trying to open or close your garage door check out this video.

Tried the reversal test on page 8 then removed 2x4 a. Your Logic Board Needs Replaced. Garage door starts down then STOPS and goes back up OR Safe-T-Beam System malfunction.

When the door is in any position other than closed and the garage door opener is activated the door will close. The logic board receives and responds signals to any remote. Sometimes it does sometimes it will go part way down and then go back up.

This allows a garage door opener to open and close your door thousands of times over its life cycle and to make it easier for you to move the door manually. One of the common service calls from garage door specialists is from property owners who keep their doors open after closing. Your garage door opens when it hits the ground.

The door opens properly but doesnt want to close. Up to 25 cash back My garage door Genie 1035 about a year old is not staying closed. Genie garage door opens fine but does not shut.

Check the Contact Reverse- see section 6 of the owners manual for testing the contact reverse Check the garage door for binding. If it is a NEW installation check the postion of the door arm. Turn the down limit switch screw clockwise one turn with a flat blade screwdriver if the garage door closes and then begins to open back up.

The cause for your Genie garage door going up but not down is attributed to a problem stemming from the sensors rollers or limit switch. Get Logic Board Replacement. Your Logic Board Needs Replaced.

There are four common problems with garage door sensors three of these homeowners can fix. Make sure ONLY the safe-t-beams that came with this garage door opener are installed. This infrared sensor passes a beam horizontally across the opening.

The garage door openers force setting may not be set correctly. Adjust the limits as needed. Check that the door manually operates correctly.

Check for and clear any obstructions in its way. Going down it goes about half way and starts to go back up using the hold method. Misaligned or blocked sensors can make your garage door fail to close.

Genie Garage Door Opener Problem. This brain can wear out in time so you could need a replacement. A garage door that stops and goes back up is usually due to malfunctioning infrared sensors.

Check if the limits are properly set. If a spring is failing your garage door opener may technically still be able to move the door but it will take far more effort and it may make shuddering movements as it goes which can. Garage door opener keeps going back up.

Genie Garage Door Opener doesnt close. Garage door starts down then STOPS and goes back up OR Safe-T-Beam System malfunction. The garage door keeps going up and down.

It closes correctly - but noisily and reversed and comes all the way back up. You might need to consider replacing it if your door is not working properly or you may purchase a new opener. Doing this can save you some amount of cash.

It goes partway down reverses direction and goes back up again. If there is such an issue you can see one of the sensor lights blinking. First you should check the safety sensors.

And in some cases the door opens as a security feature because there is something in the way. This is almost always the result of a. I called Genie and they said that it might be a sensors problem.

Up to 25 cash back Ive got a Genie garage door opener. Look at the top hinge on the door. Then look to see if the rollers are in working order.

When the logic board wears out it can cause your garage door to close then open and vice versa without explanation. It may be your garage door sensor. You push the button to close the garage door.

This is because interference with the invisible beam helps the sensors communicate. The safety sensors are blocked. Verify if there isnt a block between them.

Disconnect the Safe-T-Beam system from the garage door opener and contact Genie customer service or an authorized Genie Dealer 1-800-354-3643 Door starts down then STOPS before it is closed. Just started and weve had it for about 15 years. See How to test the balance of a garage door for more help.

They need to have a clear line-of-sight between them in order for the door to work properly. It wont close consistently. Upvote 10 01-01-06 1040 AM chadl44 Visiting Guest.

Answer 1 of 12. Additionally a simple rebooting can help. The garage door goes down then back up.

Reasons Why Your Garage Door Keeps Opening After Closing. This issue can be an easy fix. The force setting tells the opener how much resistance the door should provide and if the opener detects more than is allowed the door will reverse.

But what can you or I do if there is no object in the way. Garage door closes a little and back returns. Your garage door opens immediately after closing.

Check if the Safe-T-Beams red LED light is flashing. Safety sensors are the electronic eyes near the base of the door track on both sides. There are safety sensors at the bottom of your garage door.

It starts to close then opens up again. Get Logic Board Replacement. Malfunctioning sensors can be caused by a blockage dirty eyes loose wires or just bad sensors in general.

If your garage door opens and suddenly stops it might be because of your logic board.

Silentmax 750 3 4 Hpc Ultra Quiet Belt Drive Garage Door Opener With W The Genie Company